Soundoff-signal GHOST Surface Mount User Manual

Browse online or download User Manual for Lighting Soundoff-signal GHOST Surface Mount. SoundOff Signal GHOST Surface Mount User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
EGHST2(xx)-12 07.14
1.800.338.7337 / www.soundoffsignal.com
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
Important Information:
OPERATION:
WIRE CONNECTIONS
See setup procedure on second page.
The single GHOST® comes equipped with
an internal flasher with 33 user selectable
patterns that can be synchronized either
alternating or simultaneous with up to three
other lights. It can also be put into slave
mode and driven through an external flasher.
1. Connect the GHOST BLACK wire to a
good, convenient ground.
2. Connect the GHOST RED wire to one side
of a user supplied on/off switch. Connect
the other side of the switch, through a
5Amp fuse, to a source of
+10 - 16 Vdc.
NOTE: The GHOST is a factory sealed unit
that CANNOT be serviced in the field. Any
attempt to gain access to the GHOST unit
will most likely cause permanent damage
and void its warranty.
INSTALLATION:
Establish the mounting position on the
vehicle. Use the gasket (included) as
a template to drill three ؽ” holes for
the light wire and pilot holes for the
mounting screws. Note: pilot holes are
4
7
/
8
” on center.
Caution: Do not stretch the mounting
gasket as this may change the
required hole spacing.
WIRE HOOK-UP TABLE
WIRE COLOR: CONNECT TO:
RED +10 - 16 Vdc
BLACK Ground (-)
WHITE Pattern Select
This product contains high
intensity LED devices. To prevent
eye damage, DO NOT stare into
light beam at close range.
WARNING
!
TECHNICAL
SPECIFICATIONS
Overall Dimensions:
Single
5.65” L x 1.06” H
x 1.8 ” D
Dual
5.5” L x 2.5” H
x 1 ” D
Input Voltage: 10 - 16 Vdc
Current Consumption:
Single <1 amp
Dual <2 amps
# of LEDs:
Single 6 Generation 3 LEDs
Dual
12 Generation 3 LEDs
Operating
Temperature:
-40º to +65º C
Flash Patterns: 33
EGHST6(x)W-12
EGHST2(x)C-12
IMPORTANT INFORMATION:
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800.338.7337 (press #4 to skip the automated message).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
GHOST® SINGLE/DUAL SURFACE MOUNT LIGHT
Single Light:
Black Housing: #EGHST2(x)-12
Chrome Housing: #EGHST2(x)C-12
White Housing: #EGHST2(x)W-12
Dual Light:
Black Housing: #EGHST6(x)B-12
Chrome Housing: #EGHST6(x)C-12
White Housing: #EGHST6(x)W-12
Page view 0
1 2

Summary of Contents

Page 1 - WARNING

EGHST2(xx)-12 07.141.800.338.7337 / www.soundoffsignal.com• Warning devices are strictly regulated and governed by Federal, State and Municipal ordi

Page 2 - Flash Patterns

EGHST2(xx)-12 07.141.800.338.7337 / www.soundoffsignal.comNOTE: GHOST is equipped with Flash Pattern Recall. Once you have selected a pattern the li

Comments to this Manuals

No comments